Team R2R | 22 September 2020 | 11 MB
为什么需要多波段相关仪?宽带表并不总是显示你潜在的麻烦地区。MAAT的多波段方法警告你不要过度的立体声传播，或当你的立体声房间麦克风交付太多的反相内容。不管怎样，当混合和为单核数时，你会得到消去。
相关性衡量的是左右通道之间的关联度。如果两个信道相似，这就是单声道，它们将具有完全的相关性。当内容在一个信道中出现，而在另一个信道中出现一个反向相位版本时，在单声道中，这些累加为零，音频就消失了。
如果您的材料是注定LP分布，请记住漆切割有困难的振幅大，在非常低的频率的相位信息。2BC多orr提供了四个波段的分析关键的底部八度，六个额外的测量波段覆盖频率高达200hz，加上三个额外的波段为200到400hz范围。
除了黑胶唱片，你为什么要关注单声道音乐呢?随着电池驱动的手持聚会扬声器和无处不在的“智能扬声器”的出现，单声播放比以往任何时候都更加普遍。别忘了环绕设置的中央音箱…虽然一个产品可能为立体声播放做广告，但简单的事实是尺寸很重要。在低频率，播放从任何单一点，小型设备基本上是单耳。而且，小的声源通常根本无法再现最低的八度，许多声源开始在100赫兹以下滚动。所以一定要为你正在做的材料充分利用LF能量。
2BC多orr不仅仅是多频带相关。它还包括一个左/右平衡表，一个宽带左/右相关表，加上五个监视器控制，让你关注任何问题，你可能会遇到。
通过一个按钮，您可以切换到仅左或仅右，单键(L+R)或差键(L-R)。第五显示器控制，翻转，互换左右通道。有时你可能会遇到一个微妙的问题，你认为可能是在一个渠道或其他。翻转控制，以及仅左/右按钮，可以快速帮助确认或识别任何问题。此外，你可能偶尔会看到一些观众没有预料到的混音，Flip是一种快速旋转摄影棚到你感到舒服的地方的方法。
大多数相关仪表使用余弦刻度，从旧的模拟仪表派生而来，而2BC多orr使用一个真正的线性刻度。线性尺度更符合你的感知。
2BC多orr结合基本计量和监测控制与31波段相关表组。
细节:
与精心选择的中心频率相关的31个波段。
独家trueLinear比例为更高的精度与视觉，匹配您的感知。
立体平衡和相互关系。
五种基本的显示器控制:左、右、单反(左+右)、差(左-右)和翻转。
可折叠的UI让您只看到所需的内容。
附加功能:
包括在独立模式下运行的本机版本，非常适合专用计量。
插件运行在所有主要DAWs: AAX, AU, VST 2和VST 3。
注意:(v2.1.3 Incl仿真器)
享受Nalpeiron/Zentitle的DLL级仿真器工作!
Why do you need a multiband correlation meter? Broadband meters don’t always show you potential trouble areas. MAAT’s multiband approach warns you not to overdo stereo spread, or when your stereo room mics are delivering too much out–of–phase content. Either way, you’d get cancellation when your mix is summed to mono.
Correlation measures the degree of relatedness between left and right channel. If both channels are alike, that’s mono, and they will have perfect correlation. When content is present in one channel, and an inverted phase version is in the other channel, that sums to zero in mono and the audio disappears.
If your material is destined for LP distribution, keep in mind that lacquer cutting has difficulty with large amplitude, out–of–phase information at very low frequencies. 2BC multiCORR provides four bands of analysis for the critical bottom octave, six additional bands of metering covering frequencies up to 200 Hz, plus three additional band for the 200 to 400 Hz range.
Other than vinyl, why should you care about mono? Monaural playback is more prevalent than ever, with the rise of battery–powered, hand held party speakers and the ubiquitous “smart speaker.” Don’t forget that Center Channel speaker in a surround setup…Though a product may advertise stereo playback, the simply fact is that size matters. At low frequencies, playback from any single point, diminutive device is essentially monaural. Also, small sources usually cannot reproduce the bottom octave at all and many begin to roll off below 100 Hz. So make sure to maximize the appropriate amount of LF energy for the material you’re working on.
2BC multiCORR isn’t just multiband correlation. It also includes a left/right balance meter, a broadband left/right correlation meter, plus five monitor controls allowing you to focus on any issues you may come across.
With a single button, you can switch to Left–Only or Right–Only, Mono (L+R) or Difference (L-R). The fifth monitor control, FLIP, swaps the left and right channels. Sometimes you may come across a subtle issue that you think may be in one channel or the other. The Flip control, along with the Left–Only/Right–Only buttons, quickly helps to confirm or identify any problems. Also, you may occasionally be presented with a mix that’s not laid out from the audience prospective, and Flip is a quick way to rotate the soundstage around to where you’re comfortable.
Most correlation meters use a cosine scale, derived from old analog meters, while 2BC multiCORR employs a trueLinear scale. A linear scale better matches your perception.
2BC multiCORR combines essential metering and monitor controls with a 31 band correlation meter group.
Details:
31 bands of correlation with carefully chosen center frequencies.
Exclusive trueLinear scale for higher precision with visuals that match your perception.
Stereo Balance and Correlation.
Five essential monitor controls: Left–Only, Right–Only, Mono (L+R), Diff (L-R) and Flip.
Collapsable UI lets you see only what you need.
Extras:
Includes a native version that runs in standalone mode, great for dedicated metering.
Plug–in runs on all major DAWs: AAX, AU, VST 2 & VST 3.
Team R2R Note: (v2.1.3 Incl Emulator)
Enjoy the DLL level emulator work of Nalpeiron/Zentitle!
